PRODUCT:          Intermate Advanced Print Server (IAPS) ThinPrint
Product Release:  V 2.3

RELEASE DATE:     2006-12-14

SOFTWARE CODE:    G53_22rc_019-setup and
                  G53_22rc_019-update
  
MODELS:           200-x (x = number of active sessions supported 
                  by the license: 1, 2, 4, 8, 16, 32, or 64) 

SUPPORT SITE:     www.intermate.com/iaps

******************************************************************** 
1. This release (V2.3 G53_23rc_019 2006-02-14)
******************************************************************** 

* No changes that affect ThinPrint functionality. Release was made
  to introduce new features for TNe which shares the software base
  with ThinPrint.

********************************************************************
2. Known limitations 
********************************************************************

* Application Launcher does under devicename not accept [space] and
  other special characters. The reason is that the IAPS devicename
  is used as DNS name and subsequently must follow DNS naming
  conventions

* Number of printers per ThinPrint .print Client (by design):
  * Do not configure a single .print Client with more than 8
    printers. You can use the IAPS's multiple .print Clients to 
    distribute printing loads, even if you will be targeting
    8 or less printers from the IAPS. 

GateManager (limitations by design):
-------------------------------------
* "Go To Appliance" only works with "Manual login" (Session > 
  Preferences > "Go to Appliance".

* There are no facilities for configuration backup or applying
  configuration profiles (so the "Attach Configuration Profile"
  is, in effect, not active). "Configuration Changed" in the
  Appliance Details: General Section is not activated.
  
Printer Targets:
----------------
* If disabling SNMP for target printer communication the IAPS
  will not be able to verify of the printer is on-line.
  Check the error log in the IAPS if printing does not happen
  as expected.
  
  
********************************************************************
3. Release History
********************************************************************

******************************************************************** 
V2.2 G53_22rc_018 2006-09-11
******************************************************************** 

* ThinPrint connection service support added.

* The IAPS TP can now be used with the Application Launcher, making
  it even easier to do intial contact and configuration.
  The Launcher can set devicename, ip settings and GateManager 
  (GM) settings.

* Factory default IP mode is now DHCP, with fall back to 
  10.0.0.1

* GateManager:
  It is now possible to specify a Primary and a Secondary GM Proxy 
  address at the Configuration->GateManager page. If the IAPS cannot 
  connect to the Primary address, the Secondary address will be 
  used after approximately 1 minute.

* LPR output added.

* Secondary DNS support. New kernel firmware v62_2_07 required !!

* It is now possible to specify a Primary and a Secondary GM Proxy 
  address at the Configuration->GateManager page. If PMG cannot 
  connect to the Primary address, the Secondary address will be 
  used after approximately 1 minute.
  
* If the IAPS had once received an IP address from a DHCP server
  and later was moved to a new location without a DHCP server,
  the old IP address will appear in the IP address field in the GUI
  eventhough it functionally uses the default static address.
  Now the field will reflect the default static address 10.0.0.1

******************************************************************** 
V2.1 G53_21_013 2006-02-16
********************************************************************

* This firmware is the first in which GateManager support is fully
  implemented. Among other things:
  * You can now reboot the IAPS from the GateManager Console.
  * Appliance Details: Specific Section now includes all IP
    information.


******************************************************************** 
V1.0 G53-20-012 2006-01-31
********************************************************************

First public release.

Technical note: IAPS ThinPrint shares the software code G53 with
IAPS TNe, which is why the build number starts with G53_20.